Problems with UniDAC 4.1.4 after installing Update 4 for XE2

[RWarnecke]

Hello,

I have installed the UniDAC Componentens in version 4.1.4. When I updateded my rad studio xe2 on update 4 i get the error that the fmx161.bpl doesn't exists and the unimigwizard160.dll doesn't found. The unimigwizard160.dll is exists and the fmx161.bpl doesn't exists when update 4 for radstudio xe2 is installed. It have a new name fmx162.bpl.

Regards,

Rolf

[AlexP]

Hello,

The new build with RadStudio XE2 Update 4 support will be released today or tomorrow

[Tomasz Andrzejewski]

whats about this release?
any progress?

[Tomasz Andrzejewski]

Any chance to get this fix today?

[AlexP]

Hello,

Right now, the final testing of DAC products for RadStudio XE2 Update 4 is coming to an end. After testing finishes, we will upload the products to the site.
Most probably, the products will be available for downloading tonight.

[gandalf]

Could you give an update about the status?

Will the update be available today?

[RWarnecke]

When is the update available ? I need this update very urgently, a lot of my programs have the UniDAC Components.

[RickardEngberg]

I too am desperate for this update. I'm about to reinstall my entire Rad Studio to backtrack to update 3 just to get it working again. Please, when can I expect this update. I have been improductive for two days now.

[AndreyZ]

We are uploading all new DAC builds to our site now. They will be available today. We will make announcements at our forum about the new builds.

[RWarnecke]

I hope in the new build isn't a name requirement to a file of the installed rad studio. If so, I would update my RAD Studio with the next update only when UniDAC has been updated.

[Johan.Swart]

Hi,

I've just downloaded the latest of the UniDAC professional suite and the problem is still persisting.

I have RAD Studio XE2 with Update 4.

Please fix this ASAP. According to this forum, the problem seems to have persisted for awhile now.

Regards,
Johan

[AndreyZ]

Please check the following:
- if you don't have RAD Studio XE2 updates or you have RAD Studio XE2 Update 1, you should use UniDAC version earlier than 4.1.3, because UniDAC 4.1.3 requires RAD Studio XE2 Update 2;
- if you have RAD Studio XE2 Update 2 or RAD Studio XE2 Update 3, you should use UniDAC versions 4.1.3 or 4.1.4, because UniDAC 4.1.5 requires RAD Studio XE2 Update 4;
- if you have RAD Studio XE2 Update 4, you should use UniDAC version 4.1.5 or higher.
This compatibility problem is caused by the fact that even update versions of RAD Studio XE2 are not compatible with previous updates.
If you still encounter the problem with UniDAC and RAD Studio XE2, please specify the exact error that occurs.

[Johan.Swart]

Hi,

Thanx for the reply. I went to the download page again to make sure.

I can only see version 4.1.4 as the latest release. I purchase my license on 27 June 2011, so it should not have expired either.

Regards,
Johan

[AndreyZ]

I've redirected your question to our sales department. They will answer you soon.

[Devart]

I can only see version 4.1.4 as the latest release. I purchase my license on 27 June 2011, so it should not have expired either.

We emailed you updated credentials, please download the new version.

Regards,
Devart Support